Do It Yourself

Hi everyone...

My girlfriend's deck was built out of untreated pine that was never painted or sealed. I dont see anywhere that any wood is rotted or broken yet, but many boards are cupping from the humidity and temperature changes over the last 4 years. If I buy a few gallons of exterior wood sealant and brush on a few layers on top and bottom...

I've got one of those big red 20-gallon parts washers. You know the one. I mostly clean bicyle parts, and most bicycle lubricants are not petroleum-based. They're usually plant or wax-based. The idea is that a water-based degreaser, like Simple Green, should have no problem cleaning the stuff. My experience is that Simple...

Not sure if I should post this here or over in Technology, but here goes....

Hello, I’m back again. A couple small questions this time, nothing major. But I do have a fun story to tell to explain one of the questions. I’ll put all the questions in bulk at the end though for those who don’t care....

I'd like to build a carport. It will basically just be a shed roof extending off the front of my garage. I'll need a beam, as thin as possible, to span 22 feet from side to side....

I am looking to building my own phone from a SBC running a linux distro with plasma mobile and that can make calls....

We finished the last piece of the cat path I posted about earlier! This one goes from the laundry room, to the stairwell, and then into the guest bedroom on the upper floor (yes, I know the carpet needs replaced in that closet). They are already using them and seem to love the new path already....

tl;dr: Neighbors' galvanized fence is upside-down and very sharp and pokey. How can I make it not be?...

Hello, I’m back with another question. Everything a read is telling me yes I can, but it really does not feel right so I’m gonna ask here for good measure. Can I run electrical wire through fiberglass insulation?...

My partner and I have been talking about making some cat paths in our house since long before we owned our house. We recently got 2 new dogs, so now it is a high priority project. The first step was putting up some shelves in the hallway and making a portal from the hallway to the bedroom closet (you can see it just above the...

I have a few project ideas, and I thought of reusing the paper from various shop catalogs that I receive in my physical mailbox. I'd like to make it stiffer, something more like cardboard. I read somewhere online that you could use corn starch for this, mixed with water. Would it work? Do you have better ideas?

Hi all. I'm splitting 2 XLR line level audio signals into 3 channels each. I bought one nice device (used) online called the Whirlwind SPL1x3LL (line level). Unfortunately I can't find another used one for a decent price. However there are plenty of mic impedance matched units, SPL1x3MIC which according to the manufacturer are...

I am stripping and re-sealing a corner shower stall, and am having a hell of time removing all the old caulk. I also discovered the previous homeowners decided to just caulk over the previous caulk that was on there, so I am removing 2 or 3 layers depending on the location. It was leaking in the spots that had 3 layers so I...

I am using an old HP Pavillion 15 to make a tablet. I have all of the internal components, and am making a shell. Does anyone know what the easiest way to make a case for those parts would be?

So my roommate is a habitual cigarette smoker. He doesn't smoke indoors (thankfully) but he does smoke about every other night outdoors. I don't think he realizes that when he's done smoking the smell sort of... lingers on him and his clothes. Last night after he was done he was in the kitchen for a bit cooking. I came in this...

Hello everyone, I am pulling my home's existing ethernet cables from the garage and into my home to install a network rack. Currently my garage does not have insulation (for a future project), so it get's too hot during summer for my router to live there, so I want to install it in my mudroom where there is insulation. My...

cross-posted from: https://lemmy.dbzer0.com/post/8959162...