Do It Yourself

Hello everyone! Thank you for all the positive comments last week....

Decided to build something rather complex as a first project and it's proving challenging at ever step of the way, but I'm really proud of how it's turning out....

cross-posted from: https://beehaw.org/post/13852616...

I'm almost wrapped up with filling voids, bark inclusions, and knot holes in the boards for the bookcase. If our garage was climate controlled I expect this process would have gone faster; the same could be said if I had more horizontal working space for staging and filling. Once everything is done curing I should be able to go...

My girlfriend's deck was built out of untreated pine that was never painted or sealed. I dont see anywhere that any wood is rotted or broken yet, but many boards are cupping from the humidity and temperature changes over the last 4 years. If I buy a few gallons of exterior wood sealant and brush on a few layers on top and bottom...

I've got one of those big red 20-gallon parts washers. You know the one. I mostly clean bicyle parts, and most bicycle lubricants are not petroleum-based. They're usually plant or wax-based. The idea is that a water-based degreaser, like Simple Green, should have no problem cleaning the stuff. My experience is that Simple...

Kind of a busy week otherwise but progress is progress. I put comments on each image in the album to explain reasoning, goals, and steps taken - if you haven't done much carpentry I hope they help; if you have done much carpentry I hope you'll share your expertise. I've been around a bit and done a few things but this is not...

Not sure if I should post this here or over in Technology, but here goes....

Hello, I’m back again. A couple small questions this time, nothing major. But I do have a fun story to tell to explain one of the questions. I’ll put all the questions in bulk at the end though for those who don’t care....

I'd like to build a carport. It will basically just be a shed roof extending off the front of my garage. I'll need a beam, as thin as possible, to span 22 feet from side to side....

I am looking to building my own phone from a SBC running a linux distro with plasma mobile and that can make calls....

We finished the last piece of the cat path I posted about earlier! This one goes from the laundry room, to the stairwell, and then into the guest bedroom on the upper floor (yes, I know the carpet needs replaced in that closet). They are already using them and seem to love the new path already....

tl;dr: Neighbors' galvanized fence is upside-down and very sharp and pokey. How can I make it not be?...

tl;dr: Neighbors' galvanized fence is upside-down and very sharp and pokey. How can I make it not be?...

Hello, I’m back with another question. Everything a read is telling me yes I can, but it really does not feel right so I’m gonna ask here for good measure. Can I run electrical wire through fiberglass insulation?...

I appreciate a creative use of scrap lumber as much as the next person, but jeez. I'm getting tired of floating sistered joists and framing.

My partner and I have been talking about making some cat paths in our house since long before we owned our house. We recently got 2 new dogs, so now it is a high priority project. The first step was putting up some shelves in the hallway and making a portal from the hallway to the bedroom closet (you can see it just above the...

If you need advice that particular kind of DIY, feel free to post here and tag me or DM me directly. Hopefully I can be very helpful to some of you folks who either can't afford to pay expensive mechanics or want to learn on your own....

I'm (obviously) not great with caulk but needed to re-caulk where our kitchen counter meets the outside wall as it has a crack all along the counter. House was built about 20 years ago and it may be original and just settled....

I have a few project ideas, and I thought of reusing the paper from various shop catalogs that I receive in my physical mailbox. I'd like to make it stiffer, something more like cardboard. I read somewhere online that you could use corn starch for this, mixed with water. Would it work? Do you have better ideas?

Hi all. I'm splitting 2 XLR line level audio signals into 3 channels each. I bought one nice device (used) online called the Whirlwind SPL1x3LL (line level). Unfortunately I can't find another used one for a decent price. However there are plenty of mic impedance matched units, SPL1x3MIC which according to the manufacturer are...

I am stripping and re-sealing a corner shower stall, and am having a hell of time removing all the old caulk. I also discovered the previous homeowners decided to just caulk over the previous caulk that was on there, so I am removing 2 or 3 layers depending on the location. It was leaking in the spots that had 3 layers so I...

I posted on here the other day about some suspicious 240v cable and followed the recommendations to replace it. I was already leaning that way but was kind of hoping to be told I was overthinking it. But you all confirmed what I thought. I ran close to 25’ of 10/2 cable from the second story to the basement. Nothing is wired...

Hello,...